|Place of Origin:||CHINA|
|Minimum Order Quantity:||1 unit|
|Rated Capacity:||600W||Input Voltage:||(85V-135V)/(165-275)VAC|
|Application:||Home,Commercial,Instrumentation,home & Outdoor,Fans||BATTERY*:||Gel-780WH|
|BATTERY RATED VOLTAGE:||12/24VDC||OUTPUT VOLTAGE:||AC110V/120V//220V/230V±2%|
780WH Ups Uninterruptible Power Supply,
600W Ups Uninterruptible Power Supply,
12VDC Solar Generator Kit
PORTABLE SOLAR GENERATOR KIT
12v 50ah 780WH 600W Ups Uninterruptible Power Supply Solar Power Generator
|DC Input voltage||10.5-15V||20-29V||20-29V||40-55V||40-55V|
|AC Input voltage||(165-275)VAC|
|AC Input Frequency||45-65Hz|
|AC Output voltage||AC220V±2%(BATTERY MODE)|
|AC Output Frequency||50/60HZ±1%(BATTERY MODE)|
|DC Output voltage||2*DC 5V/1A 2*DC 5V/2.1A 1*12V/10A 1*12V/20A (BATTERY MODE)|
|Output waveform||Pure sine wave|
|Max AC Charge current||0-40A(Optional)|
|AC Charge time||5H||6H||8H||10H||12H|
|Solar input voltage||
PWM (12V TO 25V, 24V TO 50V, 48V TO 80V)
MPPT (12/24/48V TO 72V/150V)
|Solar charge current||40A|
|Solar panel *||150W||150W*2||200*2W||280W*2||330W*2|
|Solar panel charge time||6H||7H||7H||8H||8|
|Protection||Over voltage, over term, over load, short circuit, battery voltage high & low,AC input voltage high & low, automatic re-cover|
|Overload capacity||110-125%,turn to by pass after 60 secs,over 125% maintain 10 secs and then shut down|
|Communication interface||RS-232/USB (Optional)|
|Noise||≤ 45dB (with in 1 Meter)|
|Cooling||Air cooling(inner term over 45°C) when machine temperature is up to 45℃, fan works; when it’s lower than 45℃, fan stop automatically.|
After opening the package, please check the accessories, including 1 pc of user manual. And please make sure that the inverter is well-protected after transportation, if any damage:
Note: component miss, do not turn on the machine, feedback to the carrier and distributor.
1). Please retain the packing material, those can be used for next delivery if needed.
2). This series of products is heavy (check attachment as reference), please handle carefully when carrying.
1). Install in an area of well-ventilated, free of water, burning gas and corrosive stuff.
2). Not good to stand on sides, should keep good air inlet from front panel’s bottom and side face of machine, air outlet from back panel’s fan.
3). Environment temperature should remain from 0 to 40 centigrade.
4). When disassembling and operating under low temperature, it may cause water condense, should not turn on until sides of machine being dry, or it will be shock risk.
5). Install the inverter near mains socket or switch, in order to pull out mains supply plug to cut off power easily when meeting emergency.
< Loading should be turned off before connecting to inverter and turned on the loading one by one after connection completed.
< Connect inverter to accessible socket with over-current protection.
< All power sockets should link with ground protection.
< Inverter may have electricity whether input power cable inserts to mains socket or not. Turning off the inverter does not guarantee electricity does not exist. To ensure no output, should turn off all switches and cut the mains power.
< To load inductive appliances such as electromotor, displayer and laser printer, inverter capacity should be two times compared to rated power of the load.
Detail of LCD
1 Input Voltage 2 Working Mode 3 Output Voltage
4 Solar Panel 5 Battery Status 6 Loading Application
7 Silent Mode 8 Loading Status
Detail of indicate lamp & button
|INPUT||AC input voltage|
|Hz||output frequency / Working mode|
|OUTPUT||AC output voltage|
|BATT. CAPACITY||Battery working condition and capacity|
|NORMAL||AC input at normal status|
|FAULT||False signal light|
ON/OFF Button: Press for 3 seconds to turn on and 5 seconds turn off.
ENTER Button: Press for 5 seconds start to set Mode P0 to P4. Switch through UP & DOWN button.
Mode P0- Pre-set. Press ENTER 2 times to end up setting. Auto Exit after 10 seconds' no-ops.
Mode P1- Power supply setting. 01- AC supply in priority, 02- Energy saving. 03- Battery supply in priority, switch through UP & DOWN and select through ENTER button.
Mode P2- Battery Type setting. Switch through UP & DOWN and select battery type through ENTER button.
Mode P3- Charging Current 0-35A selecting. 0-20%-40%-60%-80%-100%, Maximum is 35A, Minimum 0A.
Mode P4- Voice setting. Switch the Buzzer through UP & DOWN and select through ENTER button.
|U0=Gel U.S.A||13.7V||U4=Gel European||13.8V|
|U1=A.G .M.1||13.4V||U5=Open lead acid||13.8V|
|U2=A.G .M.2||13.7V||U6=Calcium (open)||13.6V|
|U3=Sealed lead Acid||13.6V|
Terminal and output plug are both available to connect the load. Output plug can only allow the loading under 1500W. Loading over 1500W should connect to terminal.
If connect to generator, must follow the steps below:
|BATTERY Negative||Battery negative polarity connection|
|BATTERY Positive||Battery positive polarity connection|
|AC INPUT||AC input connection|
|AC OUTPUT||Universal socket output or terminal output|
|FUSE AC INPUT||Ac input voltage over current protection|
|FUSE AC OUTPUT||Ac output voltage over current protection|
If connect to generator, must follow the steps below:
●This series of inverter fairly needs maintenance. Turn to battery charge mode to extend the life of battery.
●discharge and charge the batteries at least 1 time every 6 months. Charging time should not be less than 12 hours.
●In high temperature area, battery should be charged and discharged every 2 months and standard charging time is not less than 12 hours.
●Basically batteries works 3-5 years, should replace when working not well.
●Ask professionals to replace the batteries.
|No city power input||Recoverable fuse popup||Press fuse back|
|Terminal heating||Fault or loose connection||Reconnect|
|Auto switch off with loads||Battery no power or overload||Charge battery or reduce loads|
|Switch on failure||Fault connection with city power or battery||Check connection with battery or reconnect|
|Alarm when switch on||Battery no energy or overload||Charge battery or reduce loads|
|Buzzer screams 2 secs every 3 secs||Over temperature alarm (85℃-alarm,90℃-shut down)||Check if fan or vents jammed|
|Fan’s speed not stable||Smart control according to temperature||Leave it|
Contact Person: Arms Wang